AC Repair
Technicians follow a consistent inspection sequence that records measurements before any parts are replaced. Findings are written out so the owner can see which component is outside normal range and what the options are.
Get a quoteHVAC · Felton, DE 19943
Hauser HVAC handles HVAC work across Felton and Kent County.
Technicians examine all major components to identify the root cause of any performance issue.
Every visit includes notes on equipment condition and recommended follow-up steps.
Replacement components are selected to match the specific model and age of the unit in place.
Services
Technicians follow a consistent inspection sequence that records measurements before any parts are replaced. Findings are written out so the owner can see which component is outside normal range and what the options are.
Get a quoteTechnicians follow a consistent inspection sequence on every furnace. Parts are chosen to fit the existing model rather than generic substitutes. Findings are written down so the homeowner understands what HVAC maintenance addressed.
Get a quoteWork centers on identifying the root cause of the malfunction and restoring the system to reliable operation. Technicians carry common replacement parts to complete most repairs during the initial visit when possible.
Get a quoteInstallations follow documented checklists that cover load calculations, placement clearances, and final performance verification. Each technician carries the tools and parts needed for standard residential setups.
Get a quoteTechnicians measure the house first, then select equipment that fits the actual heating load. All connections get tested on site before the crew leaves.
Get a quoteTechnicians follow a written checklist that covers safety devices, airflow, and electrical values. Findings are recorded so repeat visits can track changes rather than starting from scratch each time. The same checklist applies across properties so nothing is skipped based on location or equipment age.
Get a quoteTechnicians stick to a set sequence that starts with isolating the system and finishes with checking restored airflow. Equipment gets picked to match the duct material and layout instead of using one default setup.
Get a quoteTechnicians begin by measuring static pressure at multiple points along the supply and return lines. They compare those readings against the manufacturer specifications for the installed equipment. When pressure runs higher than expected, the next step is to locate restrictions such as crushed flex runs, closed dampers, or debris buildup inside the trunk line. Filters get removed and inspected for saturation, since a clogged filter immediately reduces volume and can cause the heat exchanger to overheat. Coils are checked for dust accumulation that narrows the gap between fins and blocks heat transfer. Once the source is confirmed, the technician explains the options for clearing or replacing the affected section before restoring normal operation.
A misreading sensor often produces short cycles or rooms that never reach the set temperature. The technician verifies that the thermostat is level, that the anticipator setting matches the system type, and that the wiring terminals show no corrosion or loose connections. Voltage drop tests are performed on the low-voltage circuit to rule out issues farther back at the control board. If the unit is older, the technician notes whether an upgrade to a programmable model would improve staging and reduce energy use without altering the existing equipment.
Why us
Consistent work standards wherever we operate in the state
We handle HVAC services for homes and businesses throughout Delaware. Every project starts with an on-site assessment, and the same technician who does that assessment carries out the work.
The technician who evaluates each job is the same person who completes the work
Scope of work and pricing details are confirmed in writing before any work starts, with changes agreed upon in advance
Frequently required parts are stocked on service vehicles to support efficient completion of jobs
Our process
The sequence begins with information gathering and ends with a written summary that the homeowner can keep. Each stage is completed before moving to the next so that findings from one step inform the work that follows.
The process starts with a review of the homeowner’s description of the symptom and any recent changes to the system. The technician then performs a visual inspection of the outdoor unit, indoor air handler or furnace, and accessible duct runs. Electrical readings are taken at the contactor, capacitor, and blower motor while the system is operating. Refrigerant pressures are measured only after confirming that airflow is within acceptable limits, because low airflow can produce misleading pressure readings. Any findings are documented and reviewed with the homeowner before any parts are ordered or replaced.
Age of the equipment, frequency of prior service, and availability of matching parts all factor into the recommendation. When the compressor or heat exchanger shows wear consistent with the unit’s service life, the technician outlines the expected remaining years of reliable operation versus the cost of a new installation. Homeowners receive a written summary that includes model numbers and measured performance values so they can compare options without pressure to decide on the spot.
The ground beneath a home plays a role in how its structure holds up through the years. Felton is built on sandy, fast-draining soil. Weather patterns determine the demands placed on heating and cooling equipment throughout the year. Felton has warm summers and cold winters, around 16 inches of snow a year, and 77 nights below freezing.
Local water quality can influence the performance of certain HVAC components that involve water. Taps in Felton deliver moderately hard water. Home systems must be selected and maintained with these factors in mind to deliver reliable performance. The presence of seasonal extremes also guides choices in equipment sizing and placement for consistent indoor comfort.
Hauser HVAC handles heating, cooling, and ventilation for homes and businesses across Delaware. Our techs see all sorts of properties and buildings, and we use the same careful approach wherever the job takes us. Delaware gets hot, humid summers and cold winters, so we stay ready for the maintenance and repairs those seasons bring.
We start every job with a system check and explain what we find in plain language. We go over recommendations and pricing before touching anything, so you know what's coming. We keep training standards the same across the state, which means steady results whether it's a tune-up, a full replacement, or an emergency fix. Response times stay as quick as the schedule and travel distances allow.
Working across Delaware over the years has taught us plenty about how different buildings deal with the seasons. Older homes often need work on the ducts or insulation. Newer places tend to focus on better efficiency. We stock parts and gear that fit what we see most around here and tweak our suggestions to the building's age, layout, and how it's used.
Customers can expect:
This keeps the work consistent from the coast to inland spots. We stick to solutions that fit what's actually there at the job site.
Pricing
The scale of the job, access to components, and condition of existing parts all affect the total. The figures below are starting points only and are not presented as quotes.
HVAC Repair — starting at $185 Furnace inspection — starting at $95 Air handler service — starting at $125 Capacitor replacement — $95-$165 Blower motor replacement — starting at $385 Thermostat replacement — $145-$225 Coil cleaning — starting at $175 Ductwork assessment — starting at $110 Refrigerant leak repair — starting at $295 Filter replacement during visit — starting at $35
Properties built before modern duct standards often have returns that are undersized or located in unconditioned spaces. Technicians note these conditions during the initial inspection and explain how they affect system efficiency. In rental units the focus is on restoring reliable operation with minimal disruption to tenants while documenting the work for the property manager.
Before a scheduled visit, clearing debris from around the outdoor cabinet and confirming that supply registers are open helps the technician reach the equipment safely. Replacing the filter a few days ahead of the appointment provides a more accurate airflow reading during the service call. These simple steps do not replace professional inspection but allow the technician to focus on internal components rather than obvious external obstructions.
FAQ
Short cycling usually traces back to an oversized unit, a dirty filter, or a thermostat that is not reading the room temperature correctly. We check the temperature differential across the equipment and the placement of the thermostat to narrow it down. In some cases the limit switch is tripping early because of restricted airflow.
Most filters slide out easily once you locate the return grille or furnace door. We can show you the correct size and direction during a visit so future changes are simple. If the system has been running with a clogged filter for a while we may still need to inspect the blower and coil.
Confirm the thermostat is set to heat and the fan switch is on auto. Check that the power switch near the furnace is on and look at the filter to see if it is blocked. These quick steps sometimes reveal a simple fix before a technician arrives.
Nearby